Quantcast Disassembly (cont) - TM-5-4210-233-14P-1_889

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: Disassembly (cont)
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Disassembly (cont) - TM-5-4210-233-14P-1_888
Up
TM-5-4210-233-14P-1 Twin Agent 4x4 Firefighting Truck Model No. CM-KFT-B Manual
Next
disassembly (cont) - TM-5-4210-233-14P-1_890
TM 5-4210-233-14&P-1 5-39.  STEERING GEAR-Continued NOTE If the side cover bearing assembly has uncaged (loose) rolls, the vertical position will allow the side cover bearing rolls to fall into the  side  cover,  where  you  may  easily  collect  and  count  them. Immediately gather all of the side cover bearing rolls and count them. CAUTION Take    care    not    to    lose    any    rolls    during    disassembly    and assembly,  or  you  will  have  to  replace  the  complete  side  cover assembly. WARNING If  the  bearing  is  the  uncaged  (loose)  roll  type,  do  not  mix  the rolls from the side cover with the rolls from the housing bearing. the bearing race and rolls are a matched set.  Interchanging the rolls  could  result  in  premature  bearing  or  seal  failure,  which could cause a loss of power steering. (12) Screw the sector shaft adjusting screw (8) through the side cover (15).  Place the side cover exterior face down and lift the sector shaft (2) out vertically. (13) Remove the retaining ring (19), the two-piece side cover seal (20), the Teflon backup washer (21), and the steel backup washer (22) from the side cover.  Discard seal and Teflon washer.  Remove and discard vent plug (23). (14) If replacement of the retainer (24) and or adjusting screw (8) is required, place the sector shaft (2) firmly in a soft jawed vise and unstake the retainer using suitable chisel.  Turn the retainer out of the sector shaft pocket and remove the adjusting screw.  Discard the retainer. (15) Loosen the worm shaft adjusting screw sealing nut (25) and loosen the worm shaft preload adjusting screw (26) approximately two turns.  Loosen the poppet adjusting screw sealing nut (27) and the poppet adjusting screw (28) approximately two turns. (16) Remove the four end cover bolts (29) and remove four washers (30). (17) Remove the end cover (31).  Some fluid will drain. NOTE The  worm  shaft  adjusting  screw  and  sealing  nut  and  poppet adjusting screw and sealing nut do not have to be removed from end   cover   (37)   unless   apparent   fluid   leaks   at   the   adjusting screws indicate the sealing nuts and or screws be replaced. (18) Remove and discard the end cover seal ring (32) from theend cover (31). (19) Remove seal protector (33) from worm shaft/input shaft (1) and discard. 5-219

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +