Quantcast Section VII. ELECTRIC MOTORS AND GENERATORS

 

Click here to make tpub.com your Home Page

Page Title: Section VII. ELECTRIC MOTORS AND GENERATORS
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Figure 71.37. Fuel pump assembly.
Up
TM-5-4210-205-12 Truck Fire Fighting; Powered Pumper; Foam and Water 500 G.M.P.; Centrifugal Pump Power Take Off Driven; 400 Gal. Water Tank 40 Gal. Manual
Next
Figure 71.38-Continued
turn clockwise to secure it to the housing.
of the plunger by slowly raising and lowering
the plunger (2) in the pump cylinder. The
202. Fuel Filter
plunger  assembly  should  move  freely
without binding or sticking. A click will be
a. Removal. Disconnect the three-inch tube (fig.
heard each time the plunger approaches the
71.6) from the elbow. Remove the fuel filter from the
top of the cylinder. This indicates that the
pipe connecting the filter to the fuel pump.
pump  interrupter  system  is  operating
b.  Repair.  Repair of the fuel filter is limited to
properly.
replacement of the element and gasket.
(2) Insert the spring (3), gasket (4), and cup (5)
c. Installation. Install in reverse of removal.
into the housing; secure with the screws.
203. Fuel Lines and Fittings
(3) Place the gasket (4) on the cover and seat
the screen (7) in the cover. Assemble these
a.  Removal.  Refer to figure 71.6 for removal
parts to the pump, being careful to guide the
sequence of the fuel lines and fittings.
screen around the cup. Use a wrench on
b. Installation. Install in reverse of removal.
the cover nut and turn the cover one-quarter
Section VII. ELECTRIC MOTORS AND GENERATORS
206. Circuit Breaker
204. Motor-Generator Assembly
a. Removal. Remove components of the
motor-generator assembly in the sequence
Refer to figure 71.38 for removal sequence.
shown in figure 71.38.
a. Removal. Refer to figure 71.38 for removal
b. Repair. Repair of the applicable compo-
sequence.
nents is limited to replacement of defective
b. Installation. Install in reverse of removal.
parts.
207. Voltage Regulator
c. Installation. Install in reverse of removal.
a. Removal. Refer to figure 71.38 for removal
sequence.
205. Components Drive Coupling
b. Installation. Install in reverse of removal.
a. Removal. Remove either the electric motor
208. Reverse Current Relay
(35, figure 71.38) or the generator (83). Slide
a. Removal. Refer to figure 71.38 for removal
the coupling (34) from the shafts of the electric
sequence.
motor and the generator.
b. Installation. Install in reverse of removal.
1
Relay assembly
13 Washer
25
Connector
36 Washer
2
Enclosure
14 Screw
26
Junction box
37 Nut
8
Relay
15 Base
27
Washer
88 Cable
4
Lead
16 Adapter
28
Nut
89 .Regulator
5
Circuit breaker
17 Connector
29
Cable
40 Connector
6
Lead
18 Cable
80
Screw
-41 Loom
7
Clamp
19 Cable assembly
81
Clamp
42 Lead
8
Connector
20 Connector
82
Connector
48 Lead
9
Terminal
21 Screw
88
Generator
44 Loom
10
Nut
22 Gasket
84
Coupling
45 Connector
11
Washer
28 Cover
85
Motor
46 Screw
12
Screw
24 Gasket
Figure 71.38. Motor-generator set.
AGO 5667A
42

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.