|
| |
TM5-4210-229-14&P
5-7.
RESCUE SAW REPAIR (Continued).
(7)
Assemble pin (141), hose (140), and shock
absorber (1 39) into either left or right bracket
and join left bracket (137) to right bracket
(134) with screw (138).
(8)
Install electronic ignition (133) on right bracket
and secure with two screws (135) and two
washers (136). Connect primary cable (87) to
ignition.
(9)
Attach bracket assembly to crankcase with
two screws (131) and two nuts (132).
(10) Assemble throttle catch (129), spring (130),
spacer (128), washer (1 27), throttle control
(126), with throttle rod (65), into rear handle
assembly, and join the left half (122) to the
right half (123) with two screws (124) and one
screw (125).
(11)
Install shock absorber (121) with two screws
(120).
(12)
Place shock absorber shaft on top of
crankcase in place provided and secure with
two screws (117) and plate (118).
(13) Secure rear of handle assembly to shock
absorber (139) with one screw (117).
(14) Install two shock absorbers (114) on front
handle (111) with two screws (115) and two
washers (116). Install front handle assembly
(111) and secure with four screws (112) and
two screws (113).
(15) Install two starter pawls (106) onto flywheel
(95) with two bolts (110), two springs (109),
two washers (108), and two nuts (107). Place
woodruff key (105) in slot provided on
crankshaft and slide flywheel (95) onto
crankshaft making sure key remains in place.
Install washer (104) and nut (103); and while
holding flywheel to prevent crankshaft from
turning, tighten nut (103).
(16) Install drive wheel (97) onto crankshaft.
Assemble centrifugal weight (102) with spring
(101) onto hub and install clutch assembly
(96) onto crankshaft with ring (179) and holder
(94). Hold the flywheel to prevent the
crankshaft from turning and tighten clutch (96)
to a snug fit.
(17) Install armature plate (93) with screws (90)
and 91) and washers (92). Attach primary coil
(89) and connect primary cable (87) and
ignition cable (88).
(18) Install muffler (83) and gasket (84) with two
screws (85) and two screws (86).
Install gasket (82), flange (81), seal (80), two
washers (79), two screws (78), gasket (77),
and carburetor (76).
(19) Install angle (75) with screw (74).
(20) Install gasket (73) and intake pipe (72) and
secure with screws (71). Place seal (70) and
spill filter (69) on intake pipe and secure with
two screws (68) and two washers (180).
(21) Connect choke rod (67) to choke shaft on
carburetor and secure with lockwasher (66).
Connect throttle rod (65) to throttle shaft on
carburetor and secure with lockwasher (64).
(22) Assemble starter assembly into fan casing
(51).
(23) Install plate (63) in fan casing with four screws
(62).
(24) Assemble starter spring (58) with starter cable
drum (57) into spring cassette. Place eyelet
of spring into cable drum then fit into place
and secure with screw (60) and nut (61).
(25) Lift up cable drum (57), pull starter cable
through hole in cable drum, then through fan
casing (5 1). Attach end of cable (56) to cable
drum. Take up a few turns of the cable and
secure cable drum with lock spring.
(26) Pull end of starter cable (56) through handle
(55) and housing (54). Tension spring (58) by
turning cable drum clockwise one or two turns.
Hold tension on spring and secure cable in
housing (54) by tying a knot.
5-20
|
