|
| |
TM5-4210-229-14&P
4-9. CHASSIS LUBRICATION INSTRUCTIONS (Continued).
a. Chassis Lubrication
(1)
Throttle Linkage. Lubricate with light engine oil (SAE 10 W 30W) (Appendix D, Item 37) as required, not
to exceed 100 hours of operation.
(2)
Spring Pin. Lubricate with grease (Appendix D, Item 20) every 100 hours of operation. Pressure gun
should be held on fitting until new grease appears.
(3)
Brake Camshaft and Slack Adjuster. Lubricate with grease (Appendix D, Item 20) every 250 hours of
operation.
(4)
Wheel Bearing. Lubricate with grease (Appendix D, Item 20) every 500 hours of operation. Pack bear-
ings with grease by hand.
(5)
Axle Shaft U Joint, and Trunnion Bearings. Lubricate with grease (Appendix D, Item 20). Lubricate
axle shaft U-joint whenever axle shafts are removed. Lubricate trunnion bearings when bearing caps are
removed for service. No periodic lubrication is required.
(6)
Tie Rod Ends. Lubricate with grease (Appendix D, Item 20) every 250 hours of operation. Pressure gun
should be held on fitting until new grease appears.
(7)
Shackle Pin. Lubricate with grease (Appendix D, Item 20) every 100 hours of operation. Pressure gun
should be held on fitting until new grease appears.
(8)
Transmission. Check transmission fluid weekly. Change transmission fluid every 250 hours of opera-
tion. Use DEXRON II type oil (Appendix D, Item 38).
(9)
Transfer Case Shift Linkage. Lubricate by hand using grease (Appendix D, Item 21) every 100 hours of
operation.
(10)
Propeller Shaft Slip Joint. Lubricate with grease (Appendix D, Item 20) every 100 hours of operation.
Pressure gun should be held on fitting until new grease appears.
(11)
Propeller Shaft U Joint. Lubricate with grease (Appendix D, Item 20) every 100 hours of operation,
pressure gun should be held on fitting until new grease appears.
(12)
Hose Reel Swing Joint. Lubricate with grease (Appendix D, Item 21) every 250 hours of operation.
(13)
Hose Reel Gears. Lubricate by hand using grease (Appendix D, Item 21) every 250 hours of operation.
(14)
Hose Reel Brake Assembly. Lubricate with grease (Appendix D, Item 20) every 250 hours of operation.
Pressure gun should be held on fitting until new grease appears.
(15)
Hose Reel Bearing. Lubricate with grease (Appendix D, Item 20) every 250 hours of operation.
(16)
Rear Differential. Remove fill plug, add SAE 80W-90 gear oil (Appendix D, Item 36) to the level of the
fill plug hole every 250 hours of operation. Change initial fill lubricant after first 50 hours of operation.
(17)
Transfer Case. Check level and fill using SAE 80W-90 gear oil (Appendix D, Item 36).
(18)
Steering Column U Joints, Slip Joints. Lubricate with grease (Appendix D, Item 20) every 250 hours of
operation Pressure gun should be held on fitting until new grease appears.
(19)
Drag Link. Lubricate with grease (Appendix D, Item 20) every 100 hours of operation. Pressure gun
should be held on fitting until new grease appears.
(20)
Power Steering Gear. Lubricate with grease (Appendix D, Item 20) every 100 hours of operation. Lu-
bricate using low pressure.
4-14
|
