 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 SB 740-95-700
Quality Defect Code
Explanation
Quality Defect Code
Explanation
33
Description or identification marking omit-
mark, or cure date). (Chargeable as a
ted, illegible, or incorrect (e.g., stock
minor defect if the correct item was
number, quantity, unit of issue, contract
shipped and a major defect if the wrong
data, or condition code).
item was shipped.)
34
Address marking omitted, illegible, or in-
55
Shelf-life date exceeded.
correct.
56
Wrong item received or selected for ship-
35
Markings improperly located or wrong
ment.
method of marking used.
57
Lubrication improper or incomplete.
36
Reserved for future use.
58
Improper identification.
37
Reserved for future use.
59
Other
(g) Group 6 (functional, certification,
38
Reserved for future use.
or performance test.
39
Reserved for future use.
(e) Group 4 (materiel deficiencies).
Quality Defect Code
Explanation
Quality Defect Code
Explanation
60
Required test not accomplished.
40
Parts, components, or controls loose, im-
61
Failed test requirements (hydraulic).
properly installed or assembled, out of
62
Failed test requirements (electrical or
adjustment, do not fit, or fail to function
electronic).
properly.
63
Failed test requirements (environmental).
41
Damaged or defective item or parts (bent,
64
Failed test requirements (mechanical).
broken, scratched, chipped, marred,
65
Failed test requirements (pressure).
cracked, warped, torn, stripped,
66
Failed certification or laboratory test.
crimped, burned, twisted, burned out,
67
Excessive heat or noise during operational
perforated, or pitted).
test.
42
Does not meet specified tolerences or re-
68
Parts or components damage (caused by
quirements (dimensional, finish,
functional failure during end item or
strength, torque, output, volume, color,
component test).
stretch, size, illumination, or weight).
69
Failed test, see table of contents for the ap-
43
Parts or components missing.
propriate appendix for the specified test
44
Wrong part or component found installed
required code (TRC).
on end item or other assembly, or used
(h) Group 7 (document, recording, or
to make up set or kit.
45
Leak (liquid): gasoline, diesel, oil, water,
routing ficiencies).
etc.
Quality Defect Code
Explanation
46
Leak (vapor): air or gas (nitrogen, oxygen,
70
Wrong count (shortage). (Chargeable as
hydrogen, etc.).
one major defect per line item if value of
47
Modified work order incompleted, im-
quantity short is $200 or more and one
properly applied, or missing.
minor defect if less than $200.)
48
Soldering, welding, brazing, metallizing, or
71 Wrong count (overage). (Chargeable as
bonding unsatisfactory.
one major defect per line item if value of
49
Reserved for future use.
quantity over is $200 or more and one
(f) Group 5 (materiel deficiencies-
minor defect if less than $200.)
continued).
72
Improper routing or process planning.
Quality Defect Code
Explanation
(Chargeable as one minor defect per line
50
Contamination (contains dirt, sludge, mois-
item.)
ture, or other foreign matter).
73
Mixed materiel (two or more stock num-
51
Excessive moisture, fungus, mildew, rot,
bers recorded under the same stock num-
infestation, or weather cracks.
ber.) (Chargeable as one minor defect
52
Item improperly classified.
per line item.)
53
Test or research required to determine
74
Historical records, including The Army
true condition classification (assign code
Maintenance Management System, TM
J or code K, per AR 725-50). (Charge-
738-750, missing, incorrect, or in-
able as one minor defect per line item.)
complete.
54
Materiel marking missing or incorrect
(e.g., serial number, data plate, piece
2-5
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals