 |
|||
|
|
|||
|
Page Title:
FM-200 SYSTEM MISCELLANEOUS MODS |
|
||
| ||||||||||
|
|
 TM55-1905-243-24&P
STATUS OF REVISION
SHEETS
APPROVED
4
3
2
1
6
5
DESCRIPTION
DATE
ZONE
REV
-
X
5
4
3
2
X
ADD SHEET 6 - EMERGENCY GEN. ROOM DAMPERS
5/30/01
M.GENTILE
A
NOTES:
16. TEMPLATE LOCATION FOR HOLD DOWN ASSEMBLY AND HINGE BRACKET FROM VENT COVER IN
CLOSED POSITION, FOR PROPER CLOSURE.
1. THIS DRAWING HAS BEEN DEVELOPED AS AN INSTALLATION DRAWING
FOR MISCELLANEOUS MODIFICATIONS ASSOCIATED WITH THE FM-200
17. FIELD FIT LENGTH OF HINGE BRACKET, FIND NO. 22, AS REQUIRED TO SUPPORT THE
FIRE SUPPRESSION SYSTEM ON THE U.S. ARMY LANDING CRAFT,
INSTALLATION OF TUNNEL VENT COVERS.
UTILITY, 2000 CLASS (LCU-2000).
18. TEMPLATE LOCATION FOR HOLD BACK ASSEMBLY FROM VENT COVER IN OPEN POSITION
2. ALL WORK SHALL BE PERFORMED UTILIZING GOOD COMMERCIAL PRACTICES
(APPROXIMATELY 45 DEGREES OPEN).
AND SHALL SATISFY THE STANDARDS, REGULATIONS, REQUIREMENTS, AND
RECOMMENDED PRACTICES OF THE CODE OF FEDERAL REGULATIONS (CFR),
19. FIELD FIT LENGTH OF CHAIN, FIND NO. 26, AS REQUIRED TO HOLD TUNNEL
AND THE STATEMENT OF WORK ASSOCIATED WITH THIS CONTRACT.
VENT COVER IN OPEN POSITION (APPROXIMATELY 45 DEGREES OPEN).
3. NEWLY INSTALLED MATERIAL, EQUIPMENT, AND DISTURBED AREAS SHALL
20. GASKET, FIND NO. 17, SHALL BE FABRICATED FROM A SHEET, 36" X 12", 3/8" THICK,
BE CLEANED, PAINTED, AND MARKED USING DEPARTMENT OF THE ARMY
NEOPRENE RUBBER, 35-45 DUROMETER HARDNESS IN ACCORDANCE WITH ASTM D 2000.
TECHNICAL BULLETIN TB 43-0144 "PAINTING OF WATERCRAFT" AS A GUIDE.
21. INSTALL GASKETS, FIND NO. 17, USING ADHESIVE, FIND NO. 25.
40
6 EA
SS
COML
KEY RING, 1"
4. EXISTING INSULATION DISTURBED OR DAMAGED BY THIS INSTALLATION
NASHUA
TAPE, METAL BACKED
181A - P/181B - FX
39
2 ROLLS
SHALL BE REPLACED OR REPAIRED TO A LIKE NEW CONDITION.
MI
ASME B16.3
38
TEE, THD. CL 300 (1/2 NPS)
5 EA
5. REMOVE AND DISCARD KNIFE EDGE AND WTRTT COVER FROM EXISTING PAINT LOCKER
37
2 EA
UNION, THD, CL 300, (1/2 NPS)
MI
ASME B16.39
POWERED EXHAUST LOUVER LOCATED BETWEEN FR 11 AND FR 12. GRIND FLUSH.
MI
36
2 EA
ELBOW, 45, THD, CL 300 (1/2 NPS)
ASME B16.3
REMOVE AND DISCARD KNIFE EDGE, LOUVER WTRTT COVER, AND ASSOCIATED
35
10 EA
ELBOW, 90, THD, CL 300, (1/2 NPS)
MI
ASME B16.3
STRUCTURE OF EXISTING PAINT LOCKER NATURAL SUPPLY LOUVER LOCATED
MI
34
40 FT
PIPE, SMLS, .840 OD X .109 WALL, (1/2 NPS)
ASTM A 53
BETWEEN FR 1 AND FR 2. OPENING LEFT BY ABOVE ITEMS SHALL BE WELDED
SS
3 EA
COML
EYE BOLTS 1/4" - 20
33
CLOSED AND GRIND FLUSH. RENEW BHD PLATING AS REQUIRED.
10 FT
COML
1/4" SS CHAIN
SS
32
GALV.
5020
31
1 EA
DAMPER, 14"W X 14"H
COML (PERFCO)
6. LENGTH OF BOLTS, FIND NO. 3, SHALL BE TRIMMED TO SUIT HOLD DOWN/BACK APPLICATION.
GALV.
5020
30
1 EA
DAMPER, 23"W X 32"H
COML (PERFCO)
BREAK SHARP EDGES AFTER TRIMMING.
5020
5150 SS
29
1 EA
DAMPER, 23"W X 32"H, 5150 SS
COML (PERFCO)
7. TEMPLATE LOCATION OF HOLD DOWN ASSEMBLY ON BHD FROM BHD LOUVER COVER,
874290
PRESSURE TRIP
28
3 EA
COML (KIDDE)
FIND NO. 1, IN OPEN POSITION.
CRES
9378T24
1 EA
S-HOOK, STANDARD, .120" WIRE DIA (100 PER PKG)
-
39428
27
COML (McMASTER CARR)
15 FT
CHAIN, SASH, TRADE SIZE 35
26
CRES
3610T32
0.40
39428
COML (McMASTER CARR)
8. DOOR SWEEP, FIND NO. 8, SHALL BE CUT TO LENGTH, TO ACCOMMODATE
46548
-
05972
25
1 EA
ADHESIVE, CYANOACRYLATE, LOCTITE NO. 404
COML (LOCTITE)
ENGINE ROOM DOOR.
STEEL
4.00
24
1 EA
WHEEL, HAND, WITHOUT HANDLE, 4 SPOKES, 7.87'' OD
WHW-15
01599
COML (REID)
0F5D5
N1801
316 SS
-
23
6 EA
NUT, WING, 3/8-16 UNC-2B
9. TEMPLATE MOUNTING HOLES ON ENGINE ROOM DOOR FROM DOOR SWEEP, FIND NO. 8,
COML (DOVER)
DRILL HOLES AND ASSEMBLE USING HARDWARE FURNISHED WITH DOOR SWEEP.
STEEL
1.70
22
4 EA
BAR, FLAT, 1/4 X 1 STK, 36" L
ASTM A 36
STEEL
0.18
21
4 EA
PLATE, 1/4 STK, 3/4" X 4"
ASTM A 36
10. TEMPLATE MOUNTING HOLES ON ENGINE ROOM DOOR JAMB FROM WEATHERSTRIPPING, FIND NO. 9,
STEEL
0.24
20
2 EA
BAR, FLAT, 1/4 X 1 1/4 STK, 2 3/4" L
ASTM A 36
DRILL HOLES AND ASSEMBLE USING HARDWARE FURNISHED WITH WEATHERSTRIPPING.
STEEL
8.01
19
2 EA
PLATE, 1/4 STK, 12'' DIA
ASTM A 36
STEEL
1.36
18
2 EA
C CHANNEL, C3 X 4.1 STK, 4" L
ASTM A 36
11. WEATHERSTRIPPING, FIND NO. 9, IS PACKAGED AS A SET. SET INCLUDES
NEOPRENE
-
17
2 EA
GASKET, 3/8 THK, 12" DIA
TWO JAMB LENGTHS AND ONE HEADER LENGTH.
SEE NOTE 20
STEEL
-
16
PIN, SPRING, 3/16" DIA, 1 1/2" L
P30
01599
1 EA
COML (REID)
12. UNIVERSAL SCREW PACK PROVIDED WITH AUTOMATIC GRIP DOOR HOLDER ASSY, FIND NO. 10,
0.04
15
2 EA
BAR, ROUND, 1/4 STK, 3" L
STEEL
ASTM A 36
IS NOT USED.
STEEL
-
14
2 EA
SCREW, TAPPING, PAN HD, TYPE I
, CROSS REC,
ASME B18.6.4
NO. 14 X 3/8'' L, ZINC CTD
13. FIELD FIT LENGTH OF ANGLE, FIND NO. 12, AS REQUIRED FOR THE INSTALLATION OF
BAR, FLAT, 1/4 X 3 STK, 3" L
STEEL
0.63
1 EA
13
ASTM A 36
AUTOMATIC GRIP DOOR HOLDER ASSY, FIND NO. 10.
STEEL
2.44
1 EA
ANGLE, 2 X 2 X 3/16 STK X 12'' L
12
ASTM A 36
STEEL
-
11
3 EA
REC,
SCREW, MACHINE, FLAT CTSK HD, TYPE II
14. FIELD FIT LOCATION FOR STRIKE PLATE, PROVIDED WITH FIND NO. 10, TO ALIGN WITH HOLDER,
ASME B18.6.3
PROVIDED WITH FIND NO. 10.
1/4-20 UNC-2A X 3/8'' L, ZINC CTD
1420A11
1.00
39428
10
1 EA
HOLDER ASSY, DOOR, AUTOMATIC GRIP
BRONZE
COML (McMASTER CARR)
15. INSTALLATION OF TUNNEL VENT CLOSURE AT WTRTT BHD 25, STBD SIDE, REQUIRES
9
1114A11
-
39428
1 EA
WEATHERSTRIPPING, SET, HEAD AND JAMB, BULB STYLE,
COML (McMASTER CARR)
THE FOLLOWING MODIFICATIONS:
FOR 3' X 7' DOOR
A. REMOVE EXISTING VENT CLOSURE GEAR OPERATOR SHAFT ASSEMBLY (TUNNEL SIDE).
17815A53
-
39428
8
1 EA
DOOR SWEEP, SINGLE FLAP NEOPRENE INSERT, CRES FLANGE
TUNNEL
COML (McMASTER CARR)
B. MOUNT WHEEL, FIND NO. 24, IN SHAFT, NEAR GEAR OPERATOR BOX.
STEEL
0.05
7
8 EA
BAR, FLAT, 1/4 X 7/8 STK, 7/8" L
ASTM A 36
C. TEMPLATE LOCATION OF MOUNTING HOLE IN SHAFT FROM WHEEL.
BAR, FLAT, 1/8 X 1 1/4 STK, 1 1/2" L
STEEL
0.08
4 EA
6
ASTM A 36
D. SECURE SHAFT AND WHEEL TOGETHER USING SPRING PIN, FIND NO. 16.
INSTALL SPRING PIN IN ACCORDANCE WITH ASME B18.8.2.
316 SS
0.03
4 EA
BAR, ROUND, 11/32 STK, 1 1/8" L
5
ASTM A 36
E. RE-INSTALL VENT CLOSURE GEAR OPERATOR SHAFT ASSEMBLY.
316 SS
9562
-
76857
4
2 EA
PAD, WELDING, 5/8" DIA, 3/4" DEPTH, 3/8-16 UNC-2B
COML (OCEANIC)
F. WHEEL SHALL BE PAINTED RED TO INDICATE ASSOCIATION WITH FM-200 VENTILATION SHUTDOWN.
316 SS
6251K999
0.30
39428
8 EA
3
BOLT, SWING, 3/8-16 UNC-2A, 3" L, ROD FULLY THREADED
COML (McMASTER CARR)
STEEL
-
4 EA
2
WASHER, PLAIN, TYPE B, RGLR, 3/8 NOM, ZINC PL
ASME B18.22.1
OUUD6
2298866
LOUVER, BHD, 17 1/2" X 13 1/2", W/RAIN LOUVER, WTRTT ALUMINUM
41.60
1
2 EA
COML (COLONIAL)
COVER, INSECT SCREEN, BLANK FLANGE, 3/8'' THK GASKET MATERIAL,
AND MONEL HARDWARE
BELOW MAIN DECK
TOTAL
UNIT
FIND
QUANTITY
CAGE
PART OR
WEIGHT
NO.
SPECIFICATION
NOMENCLATURE OR DESCRIPTION
REQUIRED
IDENTIFYING NUMBER
CODE
MATERIAL
(LB)
PARTS LIST
ENG RM ACCESS/PASSAGEWAY
CONTRACT NUMBER
UNLESS OTHERWISE SPECIFIED
U.S. ARMY TANK AUTOMOTIVE COMMAND
(ENG RM DOOR)
DIMENSIONS ARE IN INCHES
DTRSXX-XX-X-XXXXX
PAINT LOCKER
WARREN, MICHIGAN 48397-5000
A/C AND EMERGENCY
TOLERANCES ON:
CONTRACTOR
GENERATOR ROOM
2 PLACES
3 PLACES
ANGLES
U.S. ARMY LCU-2000
XXX
DISTRIBUTION STATEMENT A.
DRAWN BY
DATE
RPE (FP) CLASS APPROVAL
FM-200 SYSTEM
APPROVED FOR PUBLIC RELEASE;
BO
05/15/98
PHILIP DINENNO
CHECKER
ENGINEER
DISTRIBUTION IS UNLIMITED.
STATE OF TENNESSEE
MISCELLANEOUS MODS
JAS
MB
LIC. NO. 015882
FM-200 SYSTEM LABEL PLATES AND PLACARDS
LCU-2000-5553-4
2
CLASS DESIGN APPROVAL
AS BUILT DRAWING
SIZE
CAGE CODE
FM-200 PIPING INSTALLATION AND DETAILS
LCU-2000-5553-1
1
M. CAPUTO 8/1/03
MARK GENTILE
LCU-2000-5553-2
D
19207
NO.
DRAWING TITLE
DRAWING NUMBER
CLASS DRAWING APPROVAL
AS BUILT CHECKED
MAIN DECK
LIST OF REFERENCES
M. GENTILE 8/8/03
MARK GENTILE 4/28/99
1/1
SHEET
1 OF 6
SCALE
FO-29
FP-57/(FP-58 blank)
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals