Quantcast assembly (cont) - TM-5-4210-233-14P-1_840

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: assembly (cont)
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Assembly - TM-5-4210-233-14P-1_839
Up
TM-5-4210-233-14P-1 Twin Agent 4x4 Firefighting Truck Model No. CM-KFT-B Manual
Next
assembly (cont) - TM-5-4210-233-14P-1_841
TM 5-4210-233-14&P-1 5-25.  WATER PUMP - Continued (8) Apply film of engine oil (Item 20, Appendix E) to sealing areas of oil seal (10) and shaft (8).  Install seal with spring loaded tip towards bearing in pump housing (3).  Press or tap seal flush with water seal counterbore using suitable installing sleeve. (9) Apply a light coat of seal retainer (Item 6, Appendix E) on outside diameter of water seal (9).  Install seal in the pump body housing (3) with a sleeve large enough to fit around the seal case and resting on the brass lip.  Press seal into position. (10)   Inspect water pump impeller (7) for erosion and excessive wear. (11) If impeller is reused, the ceramic impeller insert must be replaced.  If new impeller is to be installed proceed to step 19. (12) Bake impeller assembly at 500 deg. F (260 deg. C) for one hour.  Remove insert while adhesive is hot.  Allow impeller to cool.  Clean the insert area with buffing wheel to remove old adhesive and oxide build up. WARNING Dry  cleaning  solvent  P-D-680  (safety  or  Stoddard's  solvent)  is potentially dangerous.  Avoid repeated and prolonged breathing of vapors and skin contact with the liquid.  Do no use near open flame, arcing equipment or other ignition sources.  Always wear eye protection and protective clothing.  The flash point of P-D- 680 is 100 to 138 deg. F (38 to 59 deg. C). (13)   Clean with dry cleaning solvent (Item 3, Appendix E). WARNING Death or serious injury could occur if compressed air is directed against  the  skin.    Do  not  use  compressed  air  for  cleaning  or drying  unless  the  pressure  is/has  been  reduced  to  30  psi  (2.11 kg/cm  2)  or  less.    When  working  with  compressed  air,  always use  chip  guards  eye  protection  and  other  personal  protection equipment. (14) Clean parts with compressed air. (15) Place the new adhesive washer in the impeller bond area with the new ceramic insert on top. (16) Clamp ceramic insert and impeller together with 3/8"-24 in. bolt, nut and two flat washers.  Torque to 10 ft Ibs (14 Nm). (17) Place impeller assembly in level position, insert upwards, in an oven preheated to 350 deg. F (177 deg.  C) for one hour to cure adhesive. (18) Cool impeller to room temperature and remove bolt, nut, and two flat washers. (19) Make sure mating surfaces of water seal (9) and the ceramic insert in impeller (7) are free of dirt or oil film. (20) Apply small amount of antiseize compound (Item 4, Appendix E) to the threads of the pump shaft (8). 5-170

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +