Quantcast installation - TM-5-4210-229-14P_354

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: installation
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
RESCUE SAW REPAIR (Continued). - TM-5-4210-229-14P_353
Up
TM-5-4210-229-14P Truck Firefiighting 1000 GPM Multipurpose Model 2500L Manual
Next
Section IV.  MAINTENANCE OF DIESEL FUEL INJECTION SYSTEM
TM5-4210-229-14&P 5-7. RESCUE SAW REPAIR (Continued). (27)    Pull starter cable to make sure the starter unit functions before installing fan casing (51). (28)    Install  fan  casing  (5  1)  and  secure  with  two screws (52) and three screws (53). (29)    Install seal (44) and filter holder (43) with two screws (45). (30)    Place main filter (41) inside filter cap (42) and prefilter (40) around outside of filter cap. (31)    Insert   two   screws   (48)   up   through   cylinder casing and install spacer (49) and washer (50) on each screw. (32)    Place   filter   assembly   onto   filter   holder   with screws    (48)    protruding    through    filter    cap. Install two nuts (39) and tighten. (33)    Place cylinder casing (47) over crankcase and cylinder    assembly    and    secure    with    three screws (46). (34)    Place  spring  (22)  with  two  flanges  (38)  into slot  provided  in  cutting  arm  portion  of  right crankcase   (172).      Insert   push   rod   (37)   into hole in forward end of crankcase. (35)    Install  cutting  arm  (14)  and  secure  with  nut plate (36) and screw (35). (36)    Install    eccentric    (23)    on    cutting    arm    with spacer (34), screw (32) and washer (33). (37)    Install     spacer     (31),     lock     ring     (30),     and bearings (28 and 29) into cutting arm (14). (38)    Place pulley (26) and spacer (27) on shaft (4) and  insert  shaft  through  bearings  in  cutting arm.  Install nave case (25) on shaft (4). (39)    Insert screw (16) through slot of cap rod (11), then  through  nut  plate  (36)  and  cutting  arm. Place  cutting  disc  guard  (12)  on  cutting  arm and install support (7), flange support (6), and three screws (5).  Attach upper end of cap rod (11) to guard (12) with screw (8), washer (9), gasket (10), and knob (13). (40)    With  cutting  arm  pushed  to  its  full  rearward position, install V-belt (24) on drive wheel (97) and pulley (26).  Turn eccentric (23) clockwise to    its    full    down    position    to    tension    belt. Tighten    attaching    screw    (35)    with    socket wrench. (41)    Install   clutch   cap   (20)   and   secure   with   two screws  (2  1).    Install  cutting  arm  guard  (19) and  secure  with  two  screws  (18),  then  install bushing (17) and knob (15). (42)    Install  spark  plug  (147)  and  connect  ignition cable (88). (43)    Place desired cutting disc on shaft with flange washer (3) on inside and flange washer (2) on outside and secure with screw (1). 5-23

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +