Quantcast RESCUE SAW REPAIR (Continued) - TM-5-4210-229-14P_343

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: RESCUE SAW REPAIR (Continued)
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
RESCUE SAW REPAIR (Continued) - TM-5-4210-229-14P_342
Up
TM-5-4210-229-14P Truck Firefiighting 1000 GPM Multipurpose Model 2500L Manual
Next
RESCUE SAW REPAIR (Continued) - TM-5-4210-229-14P_344
TM5-4210-229-14&P 5-7.    RESCUE SAW REPAIR (Continued). (20)   Remove screw (60) and nut (61) and remove starter    spring    cassette    and    spring    (58). Separate spring from cassette. (21)   Remove  four screws  (62) and remove plate (63). (22)   Remove    lockwasher    (64)    and    disconnect throttle rod (65) from carburetor. (23)   Remove    lockwasher    (66)    and    disconnect choke rod (67) from carburetor. (24)   Remove   two   screws   (68),and   remove   spill filter (69) with seal (70). (25)   Remove two screws (71) and remove intake pipe (72) and gasket (73). (26)   Remove screw (74) and remove angle (75). (27)   Remove   carburetor   (76),   gasket   (77),   two screws (78), two washers (79), seal (80), flange (81), and gasket (82). (28)   Remove   muffler   (83)   and   gasket   (84)   by removing   two   screws   (85)   and   two   screws (86). (29)   Disconnect   primary   cable   (87)   and   ignition cable  (88)  and  remove  transistor  coil  (89), screws    (90    and    91),    washer    (92),    and armature plate (93). (30)   Remove ring and holder (94).  Hold flywheel (95)  to  prevent  crankshaft  from  turning  and unscrew clutch assembly (96) from crank-shaft.        Remove    clutch    (96),    drive wheel  (97),  bearing  (98),  seal  (99),  and  hub (100) from crankshaft. (31)   Remove spring (101) and centrifugal weights (102). (32)   Hold  the  flywheel  to  prevent  the  crankshaft from    turning    and    remove    nut    (103)    and washer (104). (33)   Using   a   suitable   puller,   pull   flywheel   until loose and remove flywheel (95) and woodruff key (105). (34)    Remove  two  starter  pawls  (106)  from flywheel   by   removing   nuts   (107),   washers (108), springs (109) and bolts (110). (35)   Remove front handle (111) by removing four screws (112) and two screws (113). Separate shock     absorbers     (114)     from     handle     by removing two screws (115) and two washers (116). (36)   Remove    rear    handle    by    removing    three screws (117), plate (118), and two nuts (119). Remove two screws (120) and remove shock absorber (121) from right half of rear handle. (37)   Separate left hand (122) from right half (123) by removing two screws (124) and one screw (125)    and    remove    throttle    control    (126), throttle rod (65), washer (127), spacer (128), throttle catch (129) and spring (130). (38)   Remove   bracket   assembly   from   crankcase by  removing  two  screws  (131)  and  two  nuts (132). (39)   Remove  electronic  ignition  (133)  from  right bracket  (134)  by  removing  two  screws  (135) and   two   washers   (136).      Remove   primary cable (87). (40)   Separate right bracket (134) from left bracket (137)  by  removing  screw  (138)  and  remove shock   absorber   (139),   hose   (140)   and   pin (141). (41)   Remove choke button (142) and stop button (143)  by  punching  out  pins  (144).    Remove choke rod (67). (42)   Remove   screw   (145)   and   remove   contact spring (146). (43)   Remove   spark   plug   (147).      Remove   four screws  (148),  four  nuts  (149),  cylinder  (150) and gasket (151). (44)   Remove  lock  rings  (152)  and  pin  (153)  and separate piston (154) from crankshaft connecting  rod.    Remove  rings  (155)  from piston (154). 5-12

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +