Quantcast Base and Body Repair - Continued

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: Base and Body Repair - Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Base and Body Repair - Continued - TM-5-4210-220-12_416
Up
TM-5-4210-220-12 Truck Firefighting: Powered Pumper: Foam and Water 500-GPM Capacity; Centrifugal Pump Power Takeoff Driven Manual
Next
Winterization Exhaust System.
TM 5-4210-220-12 4-18.  PUMP, PIPING, AND VALVES - Continued (21) Attach gasket (35) and mounting plate (8) to base using capscrews (33) and lockwashers (34).  Tighten capscrews to 14 ft lb (19 Nm). (22) Install O-rings (30) into grooves of the rotation bearing (32). (23) Install rotation bearing (32) into base (26) and push in until it contacts the bearing shoulder. (24) Install O-ring (31) on chamfered edge of base (26). (25) Assemble the base (26) and body (29) together.  Be sure O-ring (31) is in place. (26) Slide O-ring (27) onto threaded end of rotation tube (17), past first O-ring groove and up to the collar. (27) Install rotation tube (17) through body hole (29), rotation bearing, and the base hole (26).  Align rotation tube collar to mounting hole and install screw (28). (28)    Invert the turret and balance on body end of rotation tube (17). (29) Install O-ring (25) into the rotation tube groove from the threaded end of the rotation tube. (30) Install O-ring in seal bearing groove (24). (31) Install seal bearing (24) and ball bearing (22) into base (26). (32) Install bearing retainer (21) using four screws (19) and lockwashers (20).  Tighten screws firmly. (33) Set  key  (10)  into  keyway  on  rotation  tube  (17).    Align  keyways  and  slide  link  mount  (14)  onto  rotation tube. (34) Install  rotation  nut  (16)  and  tighten  until  body  cannot  be  turned  Unscrew  rotation  nut  about  1/4  turn  or until  body can be rotated freely.  Tighten setscrew (15) firmly. (35) Apply white grease (item 34, Appendix E) to the entire length of the elevation shaft (1) and install it into the rotation tube (17) from the base end.  Use care not to damage the bushing in the body end of the rotation tube. (36) Install column link (11) into link mount (14) using stud (12) and new locknuts (13). (37) Install  cable  (9)  through  mounting  plate  (8)  and  retain  using  conduit  clamp  (7),  capscrew  (4),  and lockwasher (5). (38) Install head (6) as detailed in Head Repair, steps 10 thru 26. (39) Attach elevation link (3) to elevation shaft (1) using roll pin (2). (40) Install bumper turret as detailed in INSTALLATION preceding. 4-287

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +