Quantcast Table 2-2..  Nitrogen Pressure Regulator Temperature vs.  Pressure Corrections - TM-5-4210-218-13P_44

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: Table 2-2.. Nitrogen Pressure Regulator Temperature vs. Pressure Corrections
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Table 2-2..  Nitrogen Pressure Regulator Temperature vs.  Pressure Corrections - TM-5-4210-218-13P_43
Up
TM-5-4210-218-13P Air Conditioner Vertical Compact 6 000 BTU Manual
Next
PREPARATION FOR MOVEMENT - TM-5-4210-218-13P_45
TM 5-4210-218-13&P p. When the flow of Halon stops, start the pump by rotating the PUMP control valve 90 degrees counterclockwise. Stop the pump after each stroke and watch scale carefully to ensure that the Halon weight is 0.5 pound less than the  extinguisher  rated  capacity  (for  example,  5  pound  capacity;  fill  to  4.5  pounds)  The  remaining  Halon  will  be forced from the hose to the extinguisher with nitrogen pressurization. q. When   the   extinguisher   contains   the   appropriate   number   of   pounds   of   Halon,   close   the   ball   valve   on   the extinguisher hose. r. Place HALON/NITROGEN valve in the OFF position. s. Raise agitator bracket, with extinguisher attached, so it no longer rests on scale platform. t. Read the thermometer on scale column and adjust the nitrogen regulator gauge to the pressure according to the ambient temperature as indicated in Table 2-2. u. Open ball valve on nitrogen supply cylinder. v. Open ball valve on extinguisher hose. w. Place the HALON/NITROGEN valve in the NITROGEN position and pressurize the extinguisher. x. When correct pressure as read on the nitrogen monitor adapter assembly gauge is reached, close ball  valve  on extinguisher hose. y. Agitate fire extinguisher in bracket to reduce pressure.  If pressure is under that required, repeat steps t through y. NOTE Repeat paragraph 2-10.2 steps t.  through  y.  until  pressure  in  fire  extinguisher  is stabilized at required pressure. z. Close the fill valve on the fire extinguisher cylinder by slowly rotating the safety control valve clockwise to the SET position. aa. Place the HALON/NITROGEN valve to the OFF position. ab. Disconnect the Bradley adapter from the fire extinguisher fill valve and install cap. NOTE Place  the  filled  fire  extinguisher  aside  for  24  hours.    The  time  and  date  of  setting aside  should  be  marked  on  the  fire  extinguisher.    At  the  end  of  24  hours  repeat paragraph 2-10.2 steps w through y. NOTE The  steps  that  follow  are  to  recapture  the  Halon  left  in  the  pump  and  hoses  back into the Halon supply cylinder. ac. After all fire extinguisher are processed, verify that the valve on the Halon hose is closed. ad. Close ball valve on nitrogen supply cylinder.  Loosen nitrogen pressure regulator to nitrogen cylinder connection and bleed off nitrogen. 2-27

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +