Quantcast Section III. REMOVAL AND INSTALLATION OF MAJOR COMPONENTS

 

Click here to make tpub.com your Home Page

Page Title: Section III. REMOVAL AND INSTALLATION OF MAJOR COMPONENTS
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Chapter 2. GENERAL MAINTENANCE INSTRUCTIONS - TM-5-4210-213-350023
Up
TM-5-4210-213-35 Truck Firefighting: Powered Pumper: Foam and Water 500-GPM Capacity; Centrifugal Pump Power Takeoff Driven Manual
Next
Figure 2-1. Suction and discharge heads and screens, removal and installation.
2-8. Hose Reel Inoperative
Probable Cause
Possible Remedy
Drum will not turn...................................................................Replace or repair shaft bearings or defective drub
Sprocket teeth broken.............................................................. eplace or repair defective sprocket (para 3-18)
R
Drive motor or chain defective................................................. eplace motor or chain (TM 5-4210-213-12)
R
2-9. Water Tank Leaks or Fails to Drain Properly.
Probable Cause
Possible Remedy
Defective drain valve .............................................................. epair drain valve (para 3-6)
R
Drain filled with foreign matte.................................................Remove cover and clean draining system (para 3-20,
r
.
3-21)
Discharge line damaged.........................................................Remove cover and replace discharge line (para 3-20,
.
.
3-21)
Section III. REMOVAL AND INSTALLATION OF MAJOR COMPONENTS
2-10. General
(3) Install the foam tank and connect the tank
This section provides the information necessary to direct
fill and tank suction lines (TM -4210-213-12).
and general support, and depot maintenance personnel
(4) Install the primer pump and primer pump
for removal of the fire pump from the firetruck.
motor (TM 5-4210-213-12).
(5) Install the pump drive universal joint (TM
2-11. Fire Pump
5-4210-213-12).
(6) Install the drain line valve and lines (TM
a. Removal.
5-4210-213-12).
(1) Remove the pump suction and discharge
(7) Connect hose reel piping and wiring (TM
5-4210-213-12).
(2) Disconnect hose reel piping and wiring
(8) Install the pump suction and discharge
(TM 5-4210-213-12).
(3) Remove the drain line valve and lines
2-12. Fire Pump Suction and Discharge Heads
(TM 5-4210-213-12).
(4) Remove the pump drive universal joint
a. Removal.
(TM 5-4210-213-12).
(1) Remove the pump control panels (TM 5-
(5) Remove the primer pump and primer
4210-213-12).
pump motor (TM 5-4210-213-12).
(2) Refer to figure 2-1 and remove th
e
(6) Remove the foam tank and disconnect
suction heads from the suction and discharge lines.
the tank fill and tank suction lines (TM 5-4210-213-12).
b. Cleaning, Inspection, and Repair.
(7) Remove
the
pump
co partment
m
(1) Clean all parts with an approved cleaning
assembly by removing the four (4) U bolt assemblies
solvent, and dry thoroughly.
and disconnect the water tank fill line and water tank
(2) Inspect all parts for damaged or defective
suction line (TM 5-4210-213-12).
condition.
(8) Refer to figure 3-1 and remove the fire
(3) Replace or repair damaged or defective
pump from the fire truck.
parts as necessary.
b. Installation.
c. Installation.
(1) Refer to figure 3-1 and install the fire
(1) Refer to figure 2-1 and install the suction
pump on the fire truck.
and discharge heads on the suction and discharge lines.
(2) Install the pump compartment assembly
(2) Install the pump panels (TM 5-4210-213-
and connect water tank fill line, water tank suction line
12).
and U bolt assemblies (TM 5-4210-213-12),
2-2

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.