Quantcast Section VI. SPECIAL PURPOSE BODY, WIRING AND DATA PLATES - TM-5-4210-205-350065

 

Click here to make tpub.com your Home Page

Page Title: Section VI. SPECIAL PURPOSE BODY, WIRING AND DATA PLATES
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Figure 16. Water tank, exploded view.
Up
TM-5-4210-205-35 Truck Firefighting Powered Pumper; Foam and Water 500-GPM; Centrifugal Pump Power Takeoff Driven Manual
Next
Figure 17. Special purpose body compartments, removal and installation.
64. Water Tank, Cleaning, Inspection, and Repair
65. Water Tank, Reassembly and Installation
a. Cleaning.
Clean all parts in an approved
cleaning solvent and dry thoroughly.
a. Reassembly. Refer to figure 16 and reassemble
the water tank in the reverse order.
b. Inspection. Inspect all parts for wear, defects,
and( damage.
b. Installation.
Install the water tank (T.I 54210-
205-12).
c. Repair.  Replace or repair worn, defective, or
damaged parts as necessary.
Section VI. SPECIAL PURPOSE BODY, WIRING AND DATA PLATES
66. General
a. Refer to figure 17 and install the left- and
righthand compartments on the chassis.
The special purpose body includes the right, left,
and pump compartments.
The special purpose
b. Refer to paragraph 15 and install the pump
compartment* are bolted to the chassis frame by a
compartment on the chassis.
series of U-bolts. The right and left compartments rest
on wooden stringers attached to the chassis frame. The
c. Install the water tank and apron (TM 5-4210-
pump data plates are mounted on the special purpose
205-12).
body. The wiring will include all wiring covered by the
firetruck.  The chassis wiring harness will include the
70. Control Panel Testing and Wiring, Replacement
basic truck, plus items that have been added to the
firetruck.
a. Testing. Refer to wiring diagram (TM 5-4210-
205-12) and test a wire for continuity by disconnecting
67. Special Purpose Body Compartment, Removal
each end from the component or components to which it
is connected. With a multimeter set on the ohms scale
a. Remove the water tank and apron (TM 5-4210-
touch the test probes to each end of the wire.  If
205-12).
continuity is not indicated, the wire is defective and must
be repaired or replaced.
b. Refer to paragraph 15 and remove the pump
b. Replacement. Replace a wire by disconnecting
compartment from the chassis.
it from the component or components and remove the
wire. Install a new wire and connect it. If a broken wire
c. Refer to figure 17 and remove the left and right
is part of a wiring harness, disconnect the wire and tape
compartments from the chassis.
the ends. Install a new wire and attach it to the outside
of the wiring harness.
68. Special Purpose Body Compartments, Cleaning,
71. Chassis Wiring Harness, Replacement
Inspection, and Repair
Refer to the chassis wiring diagram (T-1 9-
a. Cleaning.
Clean all parts in an approved
2320235) and fire-truck wiring diagram (T.I 5-4210205-
cleaning solvent and dry thoroughly.
12), remove the necessary hardware and disconnect
necessary leads and remove the %wiring harness from
b. Inspection. Inspect all Farts for wear, defects,
the chassis and firetruck.
and damage.
72. Data Plates, Replacement
c. Repair.  Replace or repair worn, defective, or
damaged parts as necessary.
Remove necessary screws and rivets and
remove data plates from firetruck.
69.
Special
Purpose
Body
Compartments,
Installation
TAGO 5947-A
32

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.